Acoustic wall retrofit · ROOM phone booth
Build plan for a removable × mm slat panel on the back wall under the table: two bought panels, five printed parts, no screws. Version , as built, .
Open the 3D step-by-step manual →
checked measured or tried on the first booth, or read from the product page estimate calculated or assumed, not measured
1 · The design
Two slat panels stand side by side on the booth floor and cover the worn felt below the table. They are cut to mm wide ( whole slats) and mm long. Five printed parts push onto the top and bottom ends by hand. Nothing is screwed or glued, to the panels or to the booth.
- Two joiners (part 1) sit across the seam, one on the top end and one on the bottom end. Each holds three slats of each panel, so the pair behaves as one panel.
- Three hooks (parts 2, 3 and 4) each have a flat tab, 2 mm thick and mm long. The tabs slip between the booth's steel and the wall felt behind it: part 4 behind the flat bar of the table frame, parts 2 and 3 behind the steel frame beside the door.
- The floor carries the weight. The hooks only keep the assembly against the wall.
- Every part is numbered. The number is engraved in the back face, so you can read it while you build and nobody sees it afterwards.
What changed since version 2.2. The earlier design used one large panel in an aluminium frame, with 74 screws, printed feet and magnets. None of that is left. The panels are a ready-made set of two, the frame is replaced by five printed combs, and the booth's own steel holds the top and the left side. Materials drop from about €163 to about €
, and hands-on time from about 5 hours to about
minutes. Version 2.2 is still available
here.
Check these before you build a second booth. Three things on this page come from a description and one photo, not from measurements: (1) the height from the floor to the table frame, shown as because panels cut to fit; (2) the table, the steel bars and tubes under it, and the steel frame beside the door; (3) the exact position of the floor vent. Step 1 has you measure the first one. The other two only affect how the pictures look.
2 · Known and assumed
3 · Drawings
All dimensions in mm. Left and right always mean: as you face the wall under the table, with the door on your left. Two words are used throughout: the assembly is the two cut panels with all five printed parts on them, and each printed part has a bridge (the narrow strip over the panel end), a back plate (behind the felt, with the number), teeth (between the slats) and, on parts 2 to 4, a tab (the hook).
A · Front view, installed. Dark: the printed parts, seen between the slats and along the ends. Dashed: the three tabs, hidden behind steel. Grey on the left: the steel frame beside the door. Grey under the table: the flat bar of the table frame. The table only reaches part of the way to the door.
B · The two ends, enlarged, with the slats numbered from the left. Top end above, bottom end below. Each part pushes on from the end until its bridge touches the slat ends.
C1 · Section through the top at part 4, seen from the side. The tab goes up between the flat bar of the table frame and the wall felt.
C2 · Section through the top left corner at part 2, seen from above. Pushing the assembly to the left slides the tab behind the steel frame beside the door. Part 3 does the same at the floor.
C3 · Section at the floor through a joiner. The bridge of the bottom parts stands on the floor, so the panel itself starts mm up. The vent plate is lifted out while the panel goes in.
4 · Cutting plan
D · The two panels joined, slats up. Cut 1 is felt only, with a knife, along the outside of slat . Cut 2 goes across every slat with a fine saw. Grey areas are waste; the slat on the narrow offcut is used as the straightedge for cut 2.
Rules for another booth. Width: keep the largest number of whole slats that fits the wall; each slat changes the width by mm. Length: the measured height from the floor to the flat steel bar under the table, minus mm: for the two printed ends and to spare.
5 · Printed parts
E · The four models, each drawn from the back, the way you read its number. Seen from the back, left and right are swapped: the tabs of parts 2 and 3 point right here and left in the booth. Top right: the profile all four share.
- Same shape as the tested parts. The model was rebuilt from the session in which the clips were designed and compared with the clip3_down.stl that was printed and fitted: same outline, same volume. The only change is the engraved number, mm deep in the 2 mm back plate. The numbered files have not been printed yet.
- Material and settings. PETG or PLA, 0.4 mm nozzle, 0.2 mm layers, three walls. Colour is your choice; dark parts disappear between the slats.
- Bed size. Part 1 is mm long. It fits a 256 mm bed straight and a 220 mm bed on the diagonal.
- Changing the fit. All sizes are parameters at the top of panel_clip.scad: clearance for tight or loose teeth, felt_t to pinch the felt harder, tab_down, tab_left and tab_right for longer tabs.
6 · Parts and tools
Tools
7 · Steps
The same steps as in the 3D manual, with the same numbers.
8 · Cost and time
9 · If something does not fit
10 · Removal and limits
- Removal. Lift out the vent plate, slide the assembly to the right until both side tabs are free, pull the bottom edge toward you and lower the assembly out from under the table. The booth is left as it was.
- Not load-tested. Nobody has measured how hard you must pull to free a tab. Treat the assembly as a wall covering: do not hang anything on it and do not use it as a handhold.
- Ventilation. The assembly must not cover the floor vent. If the refitted plate touches the assembly, check that air still passes.
- Moving the booth. Take the assembly out first; only friction and the three tabs keep it in place.
11 · Checklist